Cb0178-12 load data.

CB-0178-12 (grey) wad. 7/8oz (375-382gr) crimp 8 pt, 0.055" wall depth. 12 shots, avg measured velocity was 1236 4' from muzzle, for a calculated MV of 1269fps. Std Dev 15fps. This load cycles a Maxus and a Wby SA-08. I tried it first with 16.5gr powder and it didn't consistently cycle the Wby so I bumped it up.173 posts · Joined 2006. #4 · Sep 3, 2009. For the AA hull with a 24 gram//7/8 oz shot load, try the CB1100-12. This is the Winchester 12SL copy. I see better uniformity in the patterns and more consistent crimps with good old Red Dot than with the CB0178-12L. It's also easier to pick up and stuff in the wad guide increasing production speed.Typically a fast shotgun powder is used in 12 gauge loads, often 13-15 grains of a suitable powder, 3/4 ounce or 7/8 ounce of shot. The (ClayBuster) CB 0175 and CB 0178 wads get a lot of use. ... The CB0175-15 and the CB0178-12 are interchangeable as far as stack height is concerned. The CB0175-12 has a little button inside the cup so that it ...CB100-12 vs. CB0178-12. I met my reloading supplier shooting yesterday, and set up my next big restocking order. I've only ever loaded 12G Remington Gun Clubs with: 700-X (17 gr) + WIN 209 primer + CB100-12 wads (pink), yielding 8200 psi chamber pressure and 1200 fps velocity, says the IMR web site. I've reloaded/shot about 10K of these with no ...

The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information: •Replaces the Winchester WAA12L •Optimal Load: 7/8 oz •Intended as an economical wad replacement for target and wing shooters •Wads are made with 100% prime resin for consistency These are the best wads to use for ...The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information: •Replaces the Winchester WAA12L •Optimal Load: 7/8 oz •Intended as an economical wad replacement for target and wing shooters •Wads are made with 100% prime resin for consistency These are the best wads to use for ...Mar 20, 2011 · CB0178-12 -vs- WAA12L. I read this on Ballistic Products website under reviews for the CB0178-12 wad. This wad loads fine as a WAAL substitute in 7/8 oz loads. But I also have an extra light 3/4 oz load and these wads dont work as well as the originals. They dont take up quite as much space as the Winchesters and the hulls crimp too deep and ...

The problem is finding reliable load data for Trap Shooting in an over/under or for SASS Cowboy Action in a side-by-side, if that's even a thing. Number 7-1/2 or 8 shot, 7/8 or 1 ounce, 1200 fps. ... Standard Claybuster CB0178-12 gray wad (WAA12L equiv, 7/8 oz shot), but trimmed the petals 1/8" short to fit 5. 7/8oz #7-1/2 shot 6. Overshot card ...CB0078-16 Reloading Data ~ 7/8 Ounce Shot Loads. J-Ron Inc.'s Claybuster Wad Line is a well established economical wad line built for target-shooters and wing-shooters alike. With twenty-one different models from which to choose, the Claybuster Wad Line can satisfy nearly every target or wing shooting application for reloading.

The CB2118-12 replaces the now discontinued Federal 12S3 wad. For use in 1-1/8 to 1-1/4 oz. trap, skeet, sporting clays, or hunting loads. Performs best in straight wall cases such as Federal paper or plastic and Fiocchi. Optimum load is 1-1/8 oz. Product Reviews Click here to review this item. Dished crimps on Federal hulls with 1-1/8oz loads.I've used the Claybuster CB1118-12 (WAA12 type) for some of my 1-1/8 oz loads, they seem to work OK at just a little over 1200 FPS but hadn't tried the CB0178's. I haven't had too much trouble with the crimps, but I'm only on my 2nd or 3rd time around on most of these hulls.24676 posts · Joined 2005. #2 · Mar 20, 2017. My suggestion to you is to load 7/8 oz loadings with velocity around 1250. This has been perfectly capable of cycling every 390/391 that I ever tried them in. 3/4 oz loadings at that speed can be very iffy on cycling. You can find 7/8 oz recipes for your Clays at THIS LINK.CB0178-12 is for use in WAA12L 7/8 trip, skeet or sporting clay loads. ... CB0178-12 is for use in WAA12L 7/8 trip, skeet or sporting clay loads. Performs best in tapered hulls, Remington or Winchester. Skip to Content. Back to old site If there is anything in your cart, it will not be brought over to the old site. CONFIRM CANCEL ...

The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information: •Replaces the Winchester WAA12L •Optimal Load: 7/8 oz •Intended as an economical wad replacement for target and wing shooters •Wads are made with 100% prime resin for consistency These are the best wads to use for ...

It is made for light 7/8 oz. 12 gauge loads. Link to comment Share on other sites. More sharing options... Randy Saint Eagle, SASS # 64903. Posted March 20, 2022. ... 12 to 14 gr of Red Dot or Promo,CB0178-12, 7/8 shot works great. Link to comment Share on other sites. More sharing options... watab kid. Posted March 21, 2022. watab kid.

I shoot 7/8 oz in Gun Club hulls, Win 209, 18.5 gr of Clays and the Claybuster CB0178-12 wad. Mid 1200s in velocity and just an outstanding load "We pulled the ... long time poster here once cited some patterning work that showed the light 7/8 oz. 12 ga. loads had a decidedly less tendency toward central core density with 1225 as a minimum ...Specifications. Item Width (Inches): 4.750. Item Height (Inches): 17.500. Gauge: 12 Gauge. Item Weight (lbs): 2.690. Item Length (Inches): 12.000. Show All Specifications. …CB0178-12 Wad or Downrange XXL 7/8 Pink 1 oz. loads @ approx. 1235fps. AA hull 18.6 grs. Claydot (Mec# 33) Fio 616/209 primer Downrange (DRA-12 Pink) All of the above loads crimp good in the AA hull. The 3/4 oz. load for skeet with a little tighter choke (IC) is devastating. Save Share.Win 209 primer. Claybuster CB5050-410HS wads. 296 or H110 powder (they are the same ST marks powder, so pick up which every branding name is cheaper) and this powder will give the hulls the longest reloading life. Ream the shot bushing to throw 226Gr of shot in your reloading. The stock 1/2oz bushing is going to throw about 214grs, true 1/2oz ...The Ultimate Reloading Manual. With our load data you can search by caliber, bullet weight, powder, powder manufacturer or a combination of all four. Search over 311,644 loads! Metallic Search. Shotgun Search.

On paper, 9.6 grains yields a 980 fps load with 3/4 oz shot, STS hulls and CB0178-12 wad. This is the closest I have been able to approximate the AA Featherlite loads. MEC #25 bushing, 7/8 chilled #8 shot, grey …Low recoil 12 ga. loads using Titewad powder: Winchester AA 2 3/4" hull or equivalent. Winchester WAA12L (gray) wad or Claybuster CB0 178-12. Winchester 209 Primer. 14.2 GR Titewad. Use #20 MEC Bushing. 7/8 ounce of #8 shot. This recipe was shared with me several years ago. I have used it with good success.The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information Replaces the Winchester WAA12L Optimal Load: 7/8 oz Intended as an economical w Claybuster wads are ideal for target and wing shooters.CB0178-12 grey 7/8) ... There's nothing wrong with reloading the Cleavers, the B&P's, and Clear Fiocchi's, and of course the Rio's. You'll find that they actually load better on a MEC reloader because the Euro hulls are much-much more uniform in hull length, making for a better, and more uniform crimp when compared to the Remington Gunclubs. ...I'm wanting to load some .75 oz, 12 Ga loads for skeet and have a bag of the Claybuster CB0175-12 Wads. I have been using 7/8 oz loads for a long time and Alliant ExtraLite has given the best results. I assumed it would also be the best powder for the 3/4 oz loads. In reviewing the loading data that came with the wads ExtraLite is showing ...

Federal Gold Medal Plastic. Win 209. 700x (16 gr) Claybuster CB0178-12 wad (WAA12L) 7/8 oz lead #7.5. My goal is to get a load that is as comfortable as possible for my daughter shooting for her high school trap team. She's fairly petite and the store bought shells seem to pound on her. Right now she's shooting 1145 fps 1 oz loads.John Henry. 4965 posts · Joined 2014. #20 · May 17, 2020. You should load 3/4 oz 12 ga using the 3/4 oz wad provided by Claybuster. The bag of wads contains a paper inside it with load data using Extra-Lite, 700x, and Red Dot, as well as other powders. I load several thousand of them each year, its a great load!!

12G Claybuster CB0178-12 'WAA12L' Wads (500) quantity. Add to cart. Category: Components Tags: 12, 12G, CB0178-12 ... Clone of the popular Winchester 'WAA12L'; designed for use in 7/8 to 1 oz loads. Designed for tapered hulls. Optimum load is 7/8 oz. Additional information. Weight: 0.5 kg: Dimensions: 35 × 21 × 18 cm: Gauge: 12G. Related ...The cb0178-12 wad was designed for Use in 7/8 oz to 1 oz trap, skeet, or sporting Clays loads ... This particular wad is the only one I have found that you can load 7/8oz in a AA type hull. It has a very slight taper on cup that allows it to slip past the plastic insert on the new AA. ... Box Office Data: Goodreads Book reviews ...Sep 16, 2021 · Low recoil 12 ga. loads using Titewad powder: Winchester AA 2 3/4" hull or equivalent. Winchester WAA12L (gray) wad or Claybuster CB0 178-12. Winchester 209 Primer. 14.2 GR Titewad. Use #20 MEC Bushing. 7/8 ounce of #8 shot. This recipe was shared with me several years ago. I have used it with good success. The Alliant reloading data manual contains a number of 7/8 oz loads that use the TGT-12 wad. ... I loaded some up last week because I was out of the CB0178-12 and the XXL 7/8. The breaks were not as good as the 11/16ths. load with the CB and DR wads. A 1 oz. in a Rem. hull with TGT 12 works very well IMHO.12 GAUGE LITE Hull: AA-HS or any Remington (Avoid Federals -- too much internal volume.) Shot Weight/Size: 3/4 oz. No. 9 (Actual average dropped, 315 gr.) Powder: 15.8 gr. Alliant Promo MEC Powder Bushing: No. 27 Primer: Fiocchi 616 (209), W209 or STS209 Wad: Claybuster CB0178-12 (Clone of the gray WAA12L and the best wad for …Whatcha'll runnin' for 12 ga shotgun loads? I currently have a borrowed 1897 and access to a sxs. Going to be reloading for the wife, Armay Bratt also. ... Rem or AA hulls, 14.8 gr. Extra Lite Powder (#25 MEC bushing), 3/4 oz. shot with Clay Buster CB0178-12 wads & Winchester or CCI primer. I don't get it. I use #27 bushing and throw about the ...The only effect to the stock or for that matter the shoulder is recoil which is a product of payload and acceleration. Pressure is the force against the unopened balloon that is a shot shell. A high pressure 3/4 oz. load will have less recoil than a low pressure 1 1/2 load. Shock to an old dried out gun stock is from recoil.Shotgun World General Forums. Shotshell ReloadingWAA12L wad or its Claybuster clone CB0178-12 CHRONOGRAPH RESULTS: Average velocity: 1235 High velocity: 1270 ... the 3/4 oz loads in 12 ga but, there are two other very great things about those 7/8 oz loads using Aliant's e3: 1) they're spectacular for not just skeet but trap and sporting clays as well (esp. when used with # 7 1/2 shot!), and; ...CB0178-12, DR XXL Pink, MEC78T4 You could argue about whether they are really the same or not, but at a minimum, they are at least similar. At the kind of pressures they list for the 700X-7/8 ounce loads, similar is plenty good. In fact, a CB0178-12 is real, real similar to an AA12L.

173 posts · Joined 2006. #4 · Sep 3, 2009. For the AA hull with a 24 gram//7/8 oz shot load, try the CB1100-12. This is the Winchester 12SL copy. I see better uniformity in the patterns and more consistent crimps with good old Red Dot than with the CB0178-12L. It's also easier to pick up and stuff in the wad guide increasing production speed.

With any of those (or the AA) use either the WAA12L gray wad or its Claybuster clone, the CB0178-12. They produce excellent crimps with either 7/8 or 1 oz. A MEC No. 28 bushing will give you 15.5 grains of 700-X and a No. 29 about 16.3. Use the No. 28 for a lighter load and about 1150 fps.

CB 3118-12-A Reloading Data ~ 1 1/8 Ounce Shot Loads Primer Powder Grains Pressure P.S.I AA209 E.L. 700 X 15.5 1120 9950 AA209 3 700 X 10600 AA209 E.L. Red Dot 1120 AA209 Red Dot 1150 AA209 Red Dot 18 1200 AA209 Green Dot AA209 Green Dot AA209 Green Dot AA209 E.L. Solo 1000 AA209 2 3/4 Solo 1000 AA209 3 Solo 1000Both performed well, burned clean and provided good stack heights and crimps with cb0178-12 wads. If I were to load 7/8 again I would use titewad because it costs less. ... tried RD, GD, 700X, Select, Nitro and Solo just to name a few. I started using Claybuster wads because of the cost. 7/8 loads use the CB-0178, 4100, or 8100 in Rem and Win ...The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information: •Replaces the Winchester WAA12L •Optimal Load: 7/8 oz •Intended as an economical wad replacement for target and wing shooters •Wads are made with 100% prime resin for consistency These are the best wads to use for ...As a cargo van owner, you know that finding the right load boards can be a challenge. With so many options available, it can be difficult to know which ones are best for your busin...CB0178-12: 12ga: WAA12L: Win: 7/8 oz: 500/5000: 030CBSL: Claybuster: CB1100-12: 12ga: WAA12SL: Win: 1 to 1-1/8: 500/5000: 030CBSTD: Claybuster: CB1118-12: 12ga: WAA12: Win: 1 to 1-1/8: 500/5000: 030CB781: Claybuster: CB4100-12B: 12ga: WJMR 7/8-1: Lightning: 7/8-1 oz: 500/5000: 030CBWJMR: Claybuster: CB4118-12B: 12ga: WJMR 1-1/8: WJ12: 1-1/8 oz ...CB-0178-12 (grey) wad. 7/8oz (375-382gr) crimp 8 pt, 0.055" wall depth. 12 shots, avg measured velocity was 1236 4' from muzzle, for a calculated MV of 1269fps. Std Dev 15fps. This load cycles a Maxus and a Wby SA-08. I tried it first with 16.5gr powder and it didn't consistently cycle the Wby so I bumped it up. Claybuster Wads CB0178-12. Intended as an economical wad replacement for name brand wads, Claybuster wads are ideal for target and wing shooters. Made with 100% prime resin for consistency with every loaded shell. The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Replaces the Winchester WAA12L. Performs best in tapered hulls, Remington or Winchester. Intended as an economical wad replacement for name brand wads, Claybuster wads are ideal for target and wing shooters. Made with 100% prime resin for consistency with every loaded shell. The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. SpecsI've used the Claybuster CB1118-12 (WAA12 type) for some of my 1-1/8 oz loads, they seem to work OK at just a little over 1200 FPS but hadn't tried the CB0178's. I haven't had too much trouble with the crimps, but I'm only on my 2nd or 3rd time around on most of these hulls.Intended as an economical wad replacement for name brand wads, Claybuster wads are ideal for target and wing shooters. Made with 100% prime resin for consistency with every loaded shell. Wads are essential for shotshell reloading. They fill extra space in the hull to make sure there is no room for the shot and powder to move around.CB0175-12 (3/4 oz. Wad) For use in 3/4 oz. skeet, sporting clays or hunting loads. Versatile for most hulls depending on powder volume. Optimum load is 3/4 oz. Featuring Lead-in Taper . CB0178-12 (WAA12L) For use in 7/8 to 1 oz. trap, skeet or sporting clay loads. Performs best in tapered hulls, Remington or Winchester. Optimum load is 7/8 oz.

Shotshell Reloading. CB100-12 vs. CB0178-12. Jump to Latest Follow 21 - 35 of 35 Posts. 1 ...MEC Shotshell Wads 12 Gauge 78T4 (Replaces WAA12L, CB0178-12, XXL Pink) 7/8 oz Bag of 500. Product #: 428693. Manufacturer #: MEC78T4. UPC #: 098489035910. Write the First Review Ask a Question. Our Price:10292 posts · Joined 2006. #7 · May 19, 2010. Curly has spoken the facts. The AA HS cases are best loaded with the Down Range DRA series of wads. Made in 3 sizes, they are a better fit than any of the others. The 1 oz. DRA-1 Pink wad, (Now a redish Color), is the absolute best fit in Win. AA HS cases, for 1 oz. loads.Jun 8, 2021 · On paper, 9.6 grains yields a 980 fps load with 3/4 oz shot, STS hulls and CB0178-12 wad. This is the closest I have been able to approximate the AA Featherlite loads. MEC #25 bushing, 7/8 chilled #8 shot, grey wad, WinAA, STS, or Federal Gold Medal hulls. Instagram:https://instagram. how many tables fit under 10x20 tentcraigslist longview tx partnersjail booking logs sonoma countymemegod ching cheng hanji lyrics CB0178 versus CB0175. ... Shooting Related Discussions For Sale Reloading Want to Buy/Trade Threads Gunsmithing. Top Contributors this Month View All Rick Barker 1513 Replies. Doc! 879 Replies. Ka6otm 283 Replies. Recommended Communities. AVS Forum 1M+ members. SkyscraperCity ... maggie b's cafechris plante newsmax You can certainly load 3/4 ounce 12 gauge loads. 7/8 is currently a very popular 12 gauge load which means there is a good selection of wads and recipes. Depending on the weights of the guns, you might find that 7/8 in the 12 feels the same as 3/4 in the 20. Regardless, that's the big advantage of reloading.Find load data for Accurate No. 2 propellant by clicking the button "Loads for this Powder". Accurate No. 2 is an extremely fast burning, double-base, spherical handgun powder suitable for use in a wide range of handgun calibers. Low recoil and low flash make No. 2 well suited for use in short barrel, concealed carry applications. immuno 150 vs balance of nature Heavy shot loads work well in these type of shotshells. You probably won't notice the recoil with a 1 1/8 ounce shot load. 1 ounce works. ... Commonly used Cowboy light-load wads like the gray CB0178-12 are a poor choice because they are SO long and you need room in a BP sub shotshell for more volume of powder. Like CC above, I like about 40-45 ...The CB0178-12 wad was designed for use in 7/8 oz to 1 oz trap, skeet, or sporting clays loads. Technical Information: •Replaces the Winchester WAA12L •Optimal Load: 7/8 oz •Intended as an economical wad replacement for target and wing shooters •Wads are made with 100% prime resin for consistency These are the best wads to use for ...